Menu
Industrial Automation
NX102-[][][][]
NX-Series NX1 CPU Units
![NX102-[][][][]](/Images/l_3705-22-283037-198x198.jpg)
Powerful functionality in a compact design
Related Contents
Application Solutions
- Features
- Lineup
- Specifications
- Dimensions
- Catalog / Manual / CAD / Software
last update: July 1, 2025
Electrical and Mechanical Specifications
| Item | Specification | |
|---|---|---|
| Model | NX102-[][][][] | |
| Enclosure | Mounted in a panel | |
| Dimensions (mm) *1 | 72 × 100 × 90 mm (W×H×D) | |
| Weight *2 | 390 g max. | |
| Unit power
supply |
Power supply voltage | 24 VDC (20.4 to 28.8 VDC) |
| Unit power
consumption *3 |
5.80 W max. | |
| Inrush current *4 | For cold start at room temperature:
10 A max./0.1 ms max. and 2.5 A max./150 ms max. |
|
| Current capacity of
power supply terminal *5 |
4 A max. | |
| Isolation method | No isolation: between the Unit power supply terminal and internal circuit | |
| Power supply
to the NX Unit power supply |
NX Unit power supply
capacity |
10 W max. |
| NX Unit power supply
efficiency |
80% | |
| Isolation method | No isolation: between the Unit power supply terminal and NX Unit power supply | |
| I/O Power Supply to NX Units | Not provided *6 | |
| External
connection terminal |
Communication
connector |
RJ45 for EtherNet/IP Communications × 2
RJ45 for EtherCAT Communications × 1 |
| Screwless clamping
terminal block |
For Unit power supply input and grounding (Removable) | |
| Output terminal
(service supply) |
Not provided | |
| RUN output terminal | Not provided | |
| NX bus connector | 32 NX Units can be connected | |
*1. Includes the End Cover, and does not include projecting parts.
*2. Includes the End Cover. The weight of the End Cover is 82 g.
*3. Includes an SD Memory Card. The NX Unit power consumption to NX Units is not included.
*4. The inrush current that occurs when the supplied power is changed to ON from a continuous OFF state.
The inrush current may vary depending on the operating condition and other conditions. Therefore, select fuses,
breakers, and external power supply devices that have enough margin in characteristic and capacity, considering
the condition under which the devices are used.
In particular, in case when you insert a switch to turn ON/OFF the DC power supplied from an external power supply, if
the duration of an ON-OFF-ON cycle is one second or less, the inrush control circuit may not function, which cause an
inrush current of approximately 30 A/0.3 ms.
*5. The amount of current that can be passed constantly through the terminal. Do not exceed this current value when you
use a through-wiring for the Unit power supply.
*6. When the type of the I/O power supply to NX Units you use is the supply from NX bus, an Additional I/O Power Supply
Unit is required. Refer to NX-series NX102 CPU Unit Hardware User’s Manual (W593) for details.
*2. Includes the End Cover. The weight of the End Cover is 82 g.
*3. Includes an SD Memory Card. The NX Unit power consumption to NX Units is not included.
*4. The inrush current that occurs when the supplied power is changed to ON from a continuous OFF state.
The inrush current may vary depending on the operating condition and other conditions. Therefore, select fuses,
breakers, and external power supply devices that have enough margin in characteristic and capacity, considering
the condition under which the devices are used.
In particular, in case when you insert a switch to turn ON/OFF the DC power supplied from an external power supply, if
the duration of an ON-OFF-ON cycle is one second or less, the inrush control circuit may not function, which cause an
inrush current of approximately 30 A/0.3 ms.
*5. The amount of current that can be passed constantly through the terminal. Do not exceed this current value when you
use a through-wiring for the Unit power supply.
*6. When the type of the I/O power supply to NX Units you use is the supply from NX bus, an Additional I/O Power Supply
Unit is required. Refer to NX-series NX102 CPU Unit Hardware User’s Manual (W593) for details.
General Specifications
| Item | Specification | |
|---|---|---|
| Enclosure | Mounted in a panel | |
| Grounding method | Ground to less than 100 Ω. | |
| Operating
environment |
Ambient operating
temperature |
0 to 55°C |
| Ambient operating
humidity |
10% to 95% (with no condensation) | |
| Atmosphere | Must be free from corrosive gases. | |
| Ambient storage
temperature |
-25 to 70°C (excluding battery) | |
| Altitude | 2,000 m max. | |
| Pollution degree | 2 or less: Meets IEC 61010-2-201. | |
| Noise immunity | 2 kV on power supply line (Conforms to IEC 61000-4-4.) | |
| Overvoltage category | Category II: Meets IEC 61010-2-201. | |
| EMC immunity level | Zone B | |
| Vibration resistance | Conforms to IEC 60068-2-6.
5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2 100 min each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) |
|
| Shock resistance | Conforms to IEC 60068-2-27.
147 m/s2, 3 times in X, Y, and Z directions |
|
| Battery | Life | 5 years (Power ON time rate 0% (power OFF)) |
| Model | CJ1W-BAT01 (sold separately) | |
| Applicable standards *1 | cULus, EU, UKCA, RCM, KC, NK, LR | |
*1. Refer to the consult your OMRON representative for the most recent applicable standards for each model.
Performance Specifications
| Item | NX102- | ||||||
|---|---|---|---|---|---|---|---|
| 12[][] | 11[][] | 10[][] | 90[][] | ||||
| Processing
time |
Instruction
execution times |
LD instruction | 3.3 ns | ||||
| Math instructions (for long
real data) |
70 ns or more | ||||||
| Programming | Program
capacity *1 |
Size | 5 MB | ||||
| Quantity | Number of POU
definitions |
3,000 | |||||
| Number of POU
instances |
9,000 | ||||||
| Memory
capacity for variables *2 |
Retain
attribute |
Size | 1.5 MB | ||||
| Number of
variables |
10,000 | ||||||
| No Retain
attribute |
Size | 32 MB | |||||
| Number of
variables |
90,000 | ||||||
| Data types | Number of data types | 1,000 | |||||
| Memory for
CJ-series Units (Can be specified with AT specifications for variables.) |
CIO Area | 0 to 6,144 words
(CIO 0 to CIO 6,143) *3 |
|||||
| Work Area | 0 to 512 words
(W0 to W511) *3 |
||||||
| Holding Area | 0 to 1,536 words
(H0 to H1,535) *4 |
||||||
| DM Area | 0 to 32,768 words
(D0 to D32,767) *4 |
||||||
| EM Area | 32,768 words × 25 banks
(E0_0 to E18_32,767) *4 *5 |
||||||
| Motion
control |
Number of
controlled axes *6 |
Maximum number of
controlled axes |
15 axes | 4 axes | |||
| Motion control
axes |
11 axes | --- | |||||
| Single-axis
position control axes |
4 axes | ||||||
| Maximum number of used
real axes |
12 axes | 8 axes | 6 axes | 4 axes | |||
| Used motion
control servo axes |
8 axes | 4 axes | 2 axes | --- | |||
| Used single-
axis position control servo axes |
4 axes | ||||||
| Maximum number of axes for
linear interpolation axis control |
4 axes per axes group | --- | |||||
| Number of axes for circular
interpolation axis control |
2 axes per axes group | --- | |||||
| Maximum number of axes groups | 8 axes groups | --- | |||||
| Motion control period | The same control period as that is used for the
process data communications cycle for EtherCAT. |
||||||
| Cams | Number of
cam data points |
Maximum points
per cam table |
65,535 points | ||||
| Maximum points
for all cam tables |
262,140 points | ||||||
| Maximum number of cam
tables |
160 tables | ||||||
| Position units | Pulse, mm, μm, nm, degree, and inch | ||||||
| Override factors | 0.00%, or 0.01% to 500.00% | ||||||
| Built-in
EtherNet/IP port |
Number of ports | 2 | |||||
| Physical layer | 10BASE-T/100BASE-TX | ||||||
| Frame length | 1,514 bytes max. | ||||||
| Media access method | CSMA/CD | ||||||
| Modulation | Baseband | ||||||
| Topology | Star | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Transmission media | STP (shielded, twisted-pair) cable of Ethernet
category 5, 5e or higher |
||||||
| Maximum transmission distance between
Ethernet switch and node |
100 m | ||||||
| Maximum number of cascade connections | There are no restrictions if an Ethernet switch is used. | ||||||
| CIP service:
Tag data links (cyclic com- munications) |
Maximum number of
connections |
32 per port
64 total |
|||||
| Packet interval *7 | Can be set for each connection.
1 to 10,000 ms in 1-ms increments |
||||||
| Permissible communications
band |
12,000 pps *8 *9 (including heartbeat, CIP Safety
routing) |
||||||
| Maximum number of tag sets | 32 per port
40 total *10 |
||||||
| Tag types | Network variables
CIO/WR/HR/DM/EM |
||||||
| Number of tags per
connection (i.e., per tag set) |
8 (7 tags if Controller status is included in the tag set.) | ||||||
| Maximum number of tags | 256 per port
512 total |
||||||
| Maximum link data size per
node (total size for all tags) |
19,200 bytes per port
38,400 bytes total |
||||||
| Maximum data size per
connection |
600 bytes | ||||||
| Maximum number of
registrable tag sets |
32 per port
40 total *10 (1 connection = 1 tag set) |
||||||
| Maximum tag set size | 600 bytes (Two bytes are used if Controller status is
included in the tag set.) |
||||||
| Multi-cast packet filter *11 | Supported. | ||||||
| CIP message
service: Explicit messages |
Class 3 (number of
connections) |
32 per port
64 total (clients plus server) |
|||||
| UCMM
(non- connection type) |
Maximum
number of clients that can communicate at one time |
32 per port
64 total |
|||||
| Maximum
number of servers that can communicate at one time |
32 per port
64 total |
||||||
| CIP
Safety routing |
Maximum number of
routable CIP Safety connections |
16 total | |||||
| Maximum routable
safety data length per connection |
32 bytes | ||||||
| Number of TCP sockets | 60 | ||||||
| Secure
Socket Service |
Maximum number of
Secure Socket |
60 | |||||
| TLS Version | 1.2 | ||||||
| OPC UA
Server |
Support profile/Model | Embedded 2017 UA Server Profile
PLCopen Information Model 1.00 |
|||||
| Default Endpoint/Port | opc.tcp://192.168.250.1:4840/ | ||||||
| Maximum number of sessions
(Client) |
5 | ||||||
| Maximum number of
Monitored Items per server |
2,000 | ||||||
| Sampling rate of Monitored
Items (ms) |
0, 50, 100, 250, 500, 1000, 2000, 5,000, 10,000
(If set to 0 (zero), it is assumed that is set to 50.) |
||||||
| Maximum number of
Subscriptions per server |
100 | ||||||
| Maximum number of variables
that can be published |
10,000 | ||||||
| Maximum number of structure
definitions that can be published |
100 | ||||||
| Restrictions on variables
unable to be published |
• Variables whose size is over 60 KB
• Two-dimensional or higher structure arrays (global variables) • Structures that include two-dimensional and higher arrays (global variables) • Structures with four or higher levels of nesting • Unions • Arrays whose index number suffix does no start from 0 • Arrays with 2,048 or more elements (global variables) • Structures with 100 or more members |
||||||
| SecurityPolicy/Mode | Select one of the following.
None Sign - Basic128Rsa15 Sign - Basic256 Sign - Basic256Sha256 Sign - Aes128Sha256RsaOaep Sign - Aes256Sha256RsaPss SignAndEncrypt - Basic128Rsa15 SignAndEncrypt - Basic256 SignAndEncrypt - Basic256Sha256 SignAndEncrypt - Aes128Sha256RsaOaep SignAndEncrypt - Aes256Sha256RsaPss |
||||||
| Application
Authentica- tion |
Authentication | X.509 | |||||
| Maximum
number of storable certifications |
Trusted certification: 32
Issuer certification: 32 Rejected certification: 32 |
||||||
| User
Authentica- tion |
Authentication | You can set the following items.
User name/password/role *12 Anonymous |
|||||
| Built-in
EtherCAT port |
Communications standard | IEC 61158 Type12 | |||||
| EtherCAT master specifications | Class B (Feature Pack Motion Control compliant) | ||||||
| Physical layer | 100BASE-TX | ||||||
| Modulation | Baseband | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Duplex mode | Auto | ||||||
| Topology | Line, daisy chain, branching and ring *13 | ||||||
| Transmission media | Twisted-pair cable of category 5 or higher (double-
shielded straight cable with aluminum tape and braiding) |
||||||
| Maximum transmission distance between
nodes |
100 m | ||||||
| Maximum number of slaves | 64 | ||||||
| Range of node addresses that can be set | 1 to 192 | ||||||
| Maximum process data size | Input: 5,736 bytes
Output: 5,736 bytes *14 |
||||||
| Maximum process data size per slave | Input: 1,434 bytes
Output: 1,434 bytes |
||||||
| Communications cycle | 1,000 to 32,000 μs (in 250-μs increments) | ||||||
| Sync jitter | 1 μs max. | ||||||
| Unit
configura- tion |
Units on
CPU Rack |
Maximum number of NX Units
that can be mounted to the CPU Unit |
32 | ||||
| Maximum I/O data size that
can be allocated in the CPU Unit |
Inputs: 8,192 bytes *15
Outputs: 8,192 bytes *15 |
||||||
| Maximum number of NX Units for entire
controller |
432 | ||||||
| Power supply | Model | A non-isolated power supply for DC input is built into
the CPU Unit. |
|||||
| Power OFF detection time | 2 to 8 ms | ||||||
| Internal
clock |
Accuracy *16 | At ambient temperature of 55°C:
-3.0 to +2.0 min error per month At ambient temperature of 25°C: -2.0 to +2.0 min error per month At ambient temperature of 0°C: -3.0 to +2.0 min error per month |
|||||
| Retention time of built-in capacitor | At ambient temperature of 40°C: 10 days | ||||||
*1. Execution objects and variable tables (including variable names)
*2. Memory used for CJ-series Units is included.
*3. The value can be set in 1-word increments. The value is included in the total size of variables without a Retain
attribute.
*4. The value can be set in 1-word increments. The value is included in the total size of variables with a Retain attribute.
*5. It is not possible to use the maximum number of words simultaneously for all banks, because the memory capacity for
variables with a Retain attribute is limited to 1.5 MB.
*6. For terminology, refer to the NJ/NX-series CPU Unit Motion Control User’s Manual (Cat. No. W507).
*7. Data will be refreshed at the set interval, regardless of the number of nodes.
*8. “pps” means packets per second, i.e., the number of communications packets that can be sent or received in one
second.
*9. The allowable bandwidth varies depending on the RPI of the connection in use, the primary task period, and the
number of ports simultaneously used for EtherNet/IP communications.
*10.When tag sets that exceed the total of 40 are set, a Number of Tag Sets for Tag Data Links Exceeded (840E0000 hex)
occurs.
*11.As the EtherNet/IP port implements the IGMP client, unnecessary multi-cast packets can be filtered by using an
Ethernet switch that supports IGMP Snooping.
*12.Roles can be set for the unit versions 1.64 or later of CPU Units.
*13.Ring topology is supported with the project version 1.40 or later.
Slaves on a ring topology should support a ring topology. If Omron slaves, please see the user's manual of slaves.
*14.For project unit version earlier than 1.40, the data must be within four frames.
*15.You can check the I/O allocation status with the Sysmac Studio. Refer to the NJ/NX-series CPU Unit Software User’s
Manual (Cat. No. W501) for how to check the I/O allocation status. Also, refer to the relevant manuals for specific
Units for the maximum I/O data size per NX Unit.
*16.The values shown are values in continuous operation.
*2. Memory used for CJ-series Units is included.
*3. The value can be set in 1-word increments. The value is included in the total size of variables without a Retain
attribute.
*4. The value can be set in 1-word increments. The value is included in the total size of variables with a Retain attribute.
*5. It is not possible to use the maximum number of words simultaneously for all banks, because the memory capacity for
variables with a Retain attribute is limited to 1.5 MB.
*6. For terminology, refer to the NJ/NX-series CPU Unit Motion Control User’s Manual (Cat. No. W507).
*7. Data will be refreshed at the set interval, regardless of the number of nodes.
*8. “pps” means packets per second, i.e., the number of communications packets that can be sent or received in one
second.
*9. The allowable bandwidth varies depending on the RPI of the connection in use, the primary task period, and the
number of ports simultaneously used for EtherNet/IP communications.
*10.When tag sets that exceed the total of 40 are set, a Number of Tag Sets for Tag Data Links Exceeded (840E0000 hex)
occurs.
*11.As the EtherNet/IP port implements the IGMP client, unnecessary multi-cast packets can be filtered by using an
Ethernet switch that supports IGMP Snooping.
*12.Roles can be set for the unit versions 1.64 or later of CPU Units.
*13.Ring topology is supported with the project version 1.40 or later.
Slaves on a ring topology should support a ring topology. If Omron slaves, please see the user's manual of slaves.
*14.For project unit version earlier than 1.40, the data must be within four frames.
*15.You can check the I/O allocation status with the Sysmac Studio. Refer to the NJ/NX-series CPU Unit Software User’s
Manual (Cat. No. W501) for how to check the I/O allocation status. Also, refer to the relevant manuals for specific
Units for the maximum I/O data size per NX Unit.
*16.The values shown are values in continuous operation.
Function Specifications
| Item | NX102 | |||
|---|---|---|---|---|
| Tasks | Function | I/O refreshing and the user program are
executed in units that are called tasks. Tasks are used to specify execution conditions and execution priority. |
||
| Periodically
executed tasks |
Maximum number of
primary periodic tasks |
1 | ||
| Maximum number of
periodic tasks |
2 | |||
| Conditionally
executed tasks |
Maximum number of
event tasks |
32 | ||
| Execution condition | When Activate Event Task instruction is
executed or when condition expression for variable is met |
|||
| Programming | POU
(Program Organization Unit) |
Programs | POUs that are assigned to tasks | |
| Function blocks | POUs that are used to create objects with
specific conditions |
|||
| Functions | POUs that are used to create objects that
determine unique outputs for the inputs, such as for data processing |
|||
| Programming
languages |
Types | Ladder diagrams *1 and structured text (ST) | ||
| Namespaces | A concept that is used to group identifiers for
POU definitions |
|||
| Variables | External
access of variables |
Network variables | The function which allows access from the
HMI, host computers, or other controllers |
|
| Data types | Basic data
types |
Boolean | BOOL | |
| Bit strings | BYTE, WORD, DWORD, LWORD | |||
| Integers | INT, SINT, DINT, LINT, UINT, USINT,
UDINT, ULINT |
|||
| Real numbers | REAL, LREAL | |||
| Durations | TIME | |||
| Dates | DATE | |||
| Times of day | TIME_OF_DAY | |||
| Date and time | DATE_AND_TIME | |||
| Text strings | STRING | |||
| Derivative data types | Structures, unions, enumerations | |||
| Structures | Function | A derivative data type that groups together
data with different variable types |
||
| Maximum number of
members |
2,048 | |||
| Nesting maximum
levels |
8 | |||
| Member data types | Basic data types, structures, unions,
enumerations, array variables |
|||
| Specifying member
offsets |
You can use member offsets to place
structure members at any memory locations |
|||
| Unions | Function | A derivative data type that enables access to
the same data with different data types |
||
| Maximum number of
members |
4 | |||
| Member data types | BOOL, BYTE, WORD, DWORD, LWORD | |||
| Enumerations | Function | A derivative data type that uses text strings
called enumerators to express variable values |
||
| Data type
attributes |
Array
specifications |
Function | An array is a group of elements with the
same data type. You specify the number (subscript) of the element from the first element to specify the element |
|
| Maximum number of
dimensions |
3 | |||
| Maximum number of
elements |
65,535 | |||
| Array specifications
for FB instances |
Supported | |||
| Range specifications | You can specify a range for a data type in
advance. The data type can take only values that are in the specified range |
|||
| Libraries | User libraries | |||
| Motion
control |
Control modes | Position control, velocity control, torque
control |
||
| Axis types | Servo axes, virtual servo axes, encoder
axes, virtual encoder axes, PTP axes |
|||
| Positions that can be managed | Command positions and actual positions | |||
| Single axes | Single-axis
position control |
Absolute positioning | Positioning is performed for a target position
that is specified with an absolute value |
|
| Relative positioning | Positioning is performed for a specified
travel distance from the command current position |
|||
| Interrupt feeding | Positioning is performed for a specified
travel distance from the position where an interrupt input was received from an external input |
|||
| Cyclic synchronous
absolute positioning |
A positioning command is output each
control period in Position Control Mode |
|||
| Single-axis
velocity control |
Velocity control | Velocity control is performed in Position
Control Mode |
||
| Cyclic synchronous
velocity control |
A velocity command is output each control
period in Velocity Control Mode |
|||
| Single-axis
torque control |
Torque control | The torque of the motor is controlled | ||
| Single-axis
synchronized control |
Starting cam
operation |
A cam motion is performed using the
specified cam table |
||
| Ending cam
operation |
The cam motion for the axis that is specified
with the input parameter is ended |
|||
| Starting gear
operation |
A gear motion with the specified gear ratio is
performed between a master axis and slave axis |
|||
| Positioning gear
operation |
A gear motion with the specified gear ratio
and sync position is performed between a master axis and slave axis |
|||
| Ending gear operation | The specified gear motion or positioning
gear motion is ended |
|||
| Synchronous
positioning |
Positioning is performed in sync with a
specified master axis |
|||
| Master axis phase
shift |
The phase of a master axis in synchronized
control is shifted |
|||
| Combining axes | The command positions of two axes are
added or subtracted and the result is output as the command position |
|||
| Single-axis
manual operation |
Powering the Servo | The Servo in the Servo Drive is turned ON to
enable axis motion |
||
| Jogging | An axis is jogged at a specified target
velocity |
|||
| Auxiliary
functions for single-axis control |
Resetting axis
errors |
Axes errors are cleared | ||
| Homing | A motor is operated and the limit signals,
home proximity signal, and home signal are used to define home |
|||
| Homing with
parameter |
The parameters are specified, the motor is
operated, and the limit signals, home proximity signal, and home signal are used to define home |
|||
| High-speed homing | Positioning is performed for an absolute
target position of 0 to return to home |
|||
| Stopping | An axis is decelerated to a stop | |||
| Immediately stopping | An axis is stopped immediately | |||
| Setting override
factors |
The target velocity of an axis can be changed | |||
| Changing the
current position |
The command current position or actual
current position of an axis can be changed to any position. |
|||
| Enabling external
latches |
The position of an axis is recorded when a
trigger occurs |
|||
| Disabling external
latches |
The current latch is disabled | |||
| Zone monitoring | You can monitor the command position or
actual position of an axis to see when it is within a specified range (zone) |
|||
| Enabling digital cam
switches |
You can turn a digital output ON and OFF
according to the position of an axis |
|||
| Monitoring axis
following error |
You can monitor whether the difference
between the command positions or actual positions of two specified axes exceeds a threshold value |
|||
| Resetting the
following error |
The error between the command current
position and actual current position is set to 0 |
|||
| Torque limit | The torque control function of the Servo
Drive can be enabled or disabled and the torque limits can be set to control the output torque |
|||
| Slave Axis Position
Compensation |
This function compensates the position of
the slave axis currently in synchronized control. |
|||
| Cam monitor | Outputs the specified offset position for the
slave axis in synchronous control. |
|||
| Start velocity | You can set the initial velocity when axis
motion starts |
|||
| Axes groups | Multi-axes
coordinated control |
Absolute linear
interpolation |
Linear interpolation is performed to a
specified absolute position |
|
| Relative linear
interpolation |
Linear interpolation is performed to a
specified relative position |
|||
| Circular 2D
interpolation |
Circular interpolation is performed for two
axes |
|||
| Axes group cyclic
synchronous absolute positioning |
A positioning command is output each
control period in Position Control Mode |
|||
| Auxiliary
functions for multi-axes coordinated control |
Resetting axes group
errors |
Axes group errors and axis errors are
cleared |
||
| Enabling axes groups | Motion of an axes group is enabled | |||
| Disabling axes
groups |
Motion of an axes group is disabled | |||
| Stopping axes
groups |
All axes in interpolated motion are
decelerated to a stop |
|||
| Immediately stopping
axes groups |
All axes in interpolated motion are stopped
immediately |
|||
| Setting axes group
override factors |
The blended target velocity is changed
during interpolated motion |
|||
| Reading axes group
positions |
The command current positions and actual
current positions of an axes group can be read |
|||
| Changing the axes in
an axes group |
The Composition Axes parameter in the
axes group parameters can be overwritten temporarily |
|||
| Common
items |
Cams | Setting cam table
properties |
The end point index of the cam table that is
specified in the input parameter is changed |
|
| Saving cam tables | The cam table that is specified with the input
parameter is saved in non-volatile memory in the CPU Unit |
|||
| Generating cam
tables |
The cam table is generated from the cam
property and cam node that is specified in input parameters |
|||
| Parameters | Writing MC settings | Some of the axis parameters or axes group
parameters are overwritten temporarily |
||
| Changing axis
parameters |
The axis parameters can be accessed or
changed from the user program |
|||
| Auxiliary
functions |
Count modes | You can select either Linear Mode (finite
length) or Rotary Mode (infinite length). |
||
| Unit conversions | You can set the display unit for each axis
according to the machine |
|||
| Acceleration/
deceleration control |
Automatic
acceleration/ deceleration control |
Jerk is set for the acceleration/deceleration
curve for an axis motion or axes group motion |
||
| Changing the
acceleration and deceleration rates |
You can change the acceleration or
deceleration rate even during acceleration or deceleration |
|||
| In-position check | You can set an in-position range and in-
position check time to confirm when positioning is completed |
|||
| Stop method | You can set the stop method to the
immediate stop input signal or limit input signal |
|||
| Re-execution of motion control
instructions |
You can change the input variables for a
motion control instruction during execution and execute the instruction again to change the target values during operation |
|||
| Multi-execution of motion control
instructions (Buffer Mode) |
You can specify when to start execution and
how to connect the velocities between operations when another motion control instruction is executed during operation |
|||
| Continuous axes group motions
(Transition Mode) |
You can specify the Transition Mode for
multi-execution of instructions for axes group operation |
|||
| Monitoring
functions |
Software limits | The movement range of an axis is monitored | ||
| Following error | The error between the command current
value and the actual current value is monitored for each axis |
|||
| Velocity,
acceleration rate, deceleration rate, torque, interpolation velocity, interpolation acceleration rate, interpolation deceleration rate |
You can set and monitor warning values for
each axis and each axes group |
|||
| Absolute encoder support | You can use an OMRON 1S-series
Servomotor or G5-series Servomotor with an Absolute Encoder to eliminate the need to perform homing at startup |
|||
| Input signal logic inversion | You can inverse the logic of immediate stop
input signal, positive limit input signal, negative limit input signal, or home proximity input signal |
|||
| External interface signals | The Servo Drive input signals listed below
are used. Home signal, home proximity signal, positive limit signal, negative limit signal, immediate stop signal, interrupt input signal |
|||
| Unit (I/O)
management |
EtherCAT
slaves |
Maximum number of slaves | 64 | |
| Communi-
cations |
Secure Communications | Function for secure communication with
support software |
||
| Built-in
EtherNet/IP port |
Communications protocol | TCP/IP, UDP/IP | ||
| TCP/IP
functions |
CIDR | The function which performs IP address
allocations without using a class (class A to C) of IP address |
||
| IP Forwarding | The function which forwards IP packets
between interfaces |
|||
| Packet Filter | The function which checks the IP packet to
determine whether to receive and send it based on the source IP address and TCP port number |
|||
| CIP
communica- tions service |
Tag data links | Programless cyclic data exchange is
performed with the devices on the EtherNet/IP network |
||
| Message
communications |
CIP commands are sent to or received from
the devices on the EtherNet/IP network |
|||
| CIP Safety routing | Routing function for CIP Safety on the
EtherNet/IP network. The endpoint of CIP Safety is NX-SL5[]00 in the system |
|||
| TCP/IP
applications |
Socket services | Data is sent to and received from any node
on Ethernet using the UDP or TCP protocol. Socket communications instructions are used |
||
| Secure Socket
service (Client) |
Establishes a TLS session with the TCP
protocol, and sends and receives arbitrary data to and from the server and any node on the Ethernet using instructions for secure socket communication |
|||
| FTP client | Files are transferred via FTP from the CPU
Unit to computers or controllers at other Ethernet nodes. FTP client communications instructions are used |
|||
| FTP server | Files can be read from or written to the SD
Memory Card in the CPU Unit from computers at other Ethernet nodes |
|||
| Automatic clock
adjustment |
Clock information is read from the NTP
server at the specified time or at a specified interval after the power supply to the CPU Unit is turned ON. The internal clock time in the CPU Unit is updated with the read time |
|||
| SNMP agent | Built-in EtherNet/IP port internal status
information is provided to network management software that uses an SNMP manager |
|||
| OPC UA | Server function | The function to respond to requests from
clients on the OPC UA network |
||
| EtherCAT
port |
Supported
services |
Process data
communications |
A communications method to exchange
control information in cyclic communications between the EtherCAT master and slaves. This communications method is defined by CoE |
|
| SDO
communications |
A communications method to exchange
control information in noncyclic event communications between EtherCAT master and slaves. This communications method is defined by CoE |
|||
| Network scanning | Information is read from connected slave
devices and the slave configuration is automatically generated |
|||
| DC (Distributed Clock) | Time is synchronized by sharing the
EtherCAT system time among all EtherCAT devices (including the master) |
|||
| Enable/disable settings for slaves | The slaves can be enabled or disabled as
communications targets |
|||
| Disconnecting/connecting slaves | Temporarily disconnects a slave from the
EtherCAT network for maintenance, such as for replacement of the slave, and then connects the slave again |
|||
| Supported
application protocol |
CoE | SDO messages of the CAN application can
be sent to slaves via EtherCAT |
||
| Communications instructions | CIP communications instructions, socket
communications instructions, SDO message instructions, no-protocol communications instructions, FTP client instructions, Modbus RTU protcol instructions, Modbus TCP protcol instructions |
|||
| System
management |
Event logs | Function | Events are recorded in the logs | |
| Maximum
number of events |
System event log | 768 *2
[containing] • For CPU Unit: 512 • For NX Unit without MPU: 256 |
||
| Access event log | 576
[containing] • For CPU Unit: 512 • For NX Unit without MPU: 64 |
|||
| User-defined event
log |
512 | |||
| Debugging | Online
editing |
Single | Programs, function blocks, functions, and
global variables can be changed online. More than one operators can change POUs individually via network |
|
| Forced refreshing | The user can force specific variables to
TRUE or FALSE |
|||
| Maximum
number of forced variables |
Device variables for
EtherCAT slaves |
64 | ||
| MC Test Run | Motor operation and wiring can be checked
from the Sysmac Studio |
|||
| Synchronizing | The project file in the Sysmac Studio and the
data in the CPU Unit can be made the same when online |
|||
| Differential monitoring | You can monitor when a variable changes to
TRUE or changes to FALSE |
|||
| Maximum number of monitored
variables |
8 | |||
| Data tracing | Types | Single triggered
trace |
When the trigger condition is met, the
specified number of samples are taken and then tracing stops automatically |
|
| Continuous trace | Data tracing is executed continuously and
the trace data is collected by the Sysmac Studio |
|||
| Maximum number of simultaneous
data traces |
2 | |||
| Maximum number of records | 10,000 | |||
| Sampling | Maximum number of
sampled variables |
48 | ||
| Timing of sampling | Sampling is performed for the specified task
period, at the specified time, or when a sampling instruction is executed |
|||
| Triggered traces | Trigger conditions are set to record data
before and after an event |
|||
| Trigger conditions | • When BOOL variable changes to TRUE or
FALSE • Comparison of non-BOOL variable with a constant. Comparison method: Equals (=), Greater than (>), Greater than or equals (≥), Less than (<), Less than or equals (≤), Not equal (≠) |
|||
| Delay | You can set the percentage of sampling
before and after the trigger condition is met |
|||
| Safety data
logging |
Function | Records variables used in the safety
program of the Safety CPU Unit in a chronological order |
||
| Targets | Target Safety CPU
Unit |
NX-SL5[]00 *3 | ||
| Target variable types | Exposed variables and device variables
used in the safety program |
|||
| Maximum number of
logged variables |
100 | |||
| Data types | SAFEBOOL, SAFEBYTE, SAFEWORD,
SAFEINT, SAFEDINT,BOOL, BYTE, WORD, INT, DINT |
|||
| Maximum logging
time |
480 s (Depends on logging interval) | |||
| Logging interval | Select from minimum value which stores
from primary periodic task cycle or adds constant number multiple (x1, x2, x3, x4) of primary periodic task cycle *4 |
|||
| Maximum number of simultaneous
executions |
2 | |||
| Simulation | The operation of the CPU Unit is emulated in
the Sysmac Studio |
|||
| Reliability
functions |
Self-
diagnosis |
Controller
errors |
Levels | Major faults, partial faults, minor faults,
observation, information |
| User-defined errors | User-defined errors are registered in
advance and then records are created by executing instructions |
|||
| Levels | 8 | |||
| Security | Protecting
software assets and preventing operating mistakes |
CPU Unit names and serial IDs | When going online to a CPU Unit from the
Sysmac Studio, the CPU Unit name in the project is compared to the name of the CPU Unit being connected to |
|
| Protection | User program
transfer with no restoration information |
You can prevent reading data in the CPU
Unit from the Sysmac Studio |
||
| CPU Unit write
protection |
You can prevent writing data to the CPU Unit
from the Sysmac Studio or SD Memory Card |
|||
| Overall project file
protection |
You can use passwords to protect .smc files
from unauthorized opening on the Sysmac Studio |
|||
| Data protection | You can use passwords to protect POUs on
the Sysmac Studio |
|||
| Verification of operation authority | Online operations can be restricted by
operation rights to prevent damage to equipment or injuries that may be caused by operating mistakes |
|||
| Number of groups | 5 | |||
| User Authentication | This function authenticates each user
when Sysmac Studio is going online with the Controller and restricts operation according to the user's privileges. |
|||
| Number of groups | 5 | |||
| Verification of user program
execution ID |
The user program cannot be executed
without entering a user program execution ID from the Sysmac Studio for the specific hardware (CPU Unit) |
|||
| SD Memory
Card functions |
Storage type | SD Memory Card, SDHC Memory Card | ||
| Application | Automatic transfer from SD
Memory Card |
When the power supply to the controller is
turned ON, the data that is stored in the autoload directory of the SD Memory Card is transferred to the controller |
||
| Program transfer from SD Memory
Card |
With the specification of the system-defined
variable, you can transfer a program that is stored in the SD Memory Card to the controller |
|||
| SD Memory Card operation
instructions |
You can access SD Memory Cards from
instructions in the user program |
|||
| File operations from the Sysmac
Studio |
You can perform file operations for controller
files in the SD Memory Card and read/write standard document files on the computer |
|||
| SD Memory Card life expiration
detection |
Notification of the expiration of the life of the
SD Memory Card is provided in a system- defined variable and event log |
|||
| Backing up
data |
SD Memory
Card backups |
Operating
methods |
CPU Unit front-
panel DIP switch |
You can perform backup, verification, and
restoration operations by manipulating the front-panel DIP switch on the CPU Unit |
| Specification with
system-defined variables |
You can perform backup, verification, and
restoration operations by manipulating system-defined variables |
|||
| SD Memory Card
Window in Sysmac Studio |
Backup and verification operations are
performed from the SD Memory Card Window of the Sysmac Studio |
|||
| Special instruction | The special instruction is used to backup
data |
|||
| Protection | Disabling backups to
SD Memory Cards |
Backing up data to a SD Memory Card is
prohibited |
||
| Safety Unit Restore from SD Memory Card | Restores the data of the Safety CPU Unit
using the front-panel DIP switch on the Safety CPU Unit and SD Memory Card |
|||
| Sysmac Studio Controller backups | The Sysmac Studio is used to backup,
restore, or verify controller data |
|||
*1. Inline ST is supported. (Inline ST is ST that is written as an element in a ladder diagram.)
*2. Up to 512 system logs for events in the CPU Unit and 256 system logs in the NX Unit can be recorded.
*3. When connected to a CPU rack.
*4. Minimum value fulfills all these conditions.
• Larger than 5 ms
• Constant number multiple of primary periodic task cycle
*2. Up to 512 system logs for events in the CPU Unit and 256 system logs in the NX Unit can be recorded.
*3. When connected to a CPU rack.
*4. Minimum value fulfills all these conditions.
• Larger than 5 ms
• Constant number multiple of primary periodic task cycle
Function Specifications of the Database Connection CPU Units
Besides functions of the NX102-[][][][], functions supported by the NX102-[][]20 are as follows.
| Item | Description | |||||
|---|---|---|---|---|---|---|
| NX102-1220 | NX102-1120 | NX102-1020 | NX102-9020 | |||
| Supported port | Built-in EtherNet/IP port | |||||
| Supported
DB versions *1 *2 |
SQL Server by Microsoft | 2012/2014/2016/2017/2019/2022 | ||||
| Oracle Database by Oracle | 11g/12c/18c/19c/21c/23ai (23c) | |||||
| DB2 for Linux, UNIX and
Windows by IBM |
9.7/10.1/10.5/11.1 | |||||
| MySQL Community Edition
by Oracle*3 |
5.6/5.7/8.0 | |||||
| Firebird by Firebird
Foundation |
2.5 | |||||
| PostgreSQL by PostgreSQL
Global Development Group |
9.4/9.5/9.6/10/11/12/13/14/15/16 | |||||
| Number of DB Connections (Number of
databases that can be connected at the same time) |
2 *4 *5 | |||||
| Instruction | Supported operations | The following operations can be performed by executing DB Connection
Instructions in the CPU Units: Inserting records (INSERT), Updating records (UPDATE), Retrieving records (SELECT), Deleting records (DELETE), Execute Stored Procedure*6, and Execute Batch Insert*6 |
||||
| Max. number of instructions
for simultaneous execution |
32 | |||||
| Max. number of columns in
an INSERT operation |
SQL Server: 1,024
Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in
an UPDATE operation |
SQL Server: 1,024
Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in
a SELECT operation |
SQL Server: 1,024
Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of records in
the output of a SELECT operation |
65,535 elements, 4 MB | |||||
| Stored
procedure call *6 |
Supported
databases |
• SQL Server
• Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Argument
(Sum of IN, OUT and INOUT) |
Up to 256 variables*7 | |||||
| Return value | One variable | |||||
| Result set | Supported | |||||
| Spool function | Not supported | |||||
| Batch
insert execution *6 |
Supported
databases |
• SQL Server
• Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Supported data
size |
Less than 1,000 columns and upper limit (8 MB) of structure variable size
or less*8 |
|||||
| Spool function | Not supported | |||||
| Max. number of DB Map
Variables for which a mapping can be connected *9 |
SQL Server: 30*10
Oracle: 20*10 DB2: 20*10 MySQL: 20*10 Firebird: 15 PostgreSQL: 20*10 |
|||||
| Run mode of the DB Connection Service | Operation Mode or Test Mode
• Operation Mode: When each instruction is executed, the service actually accesses the DB • Test Mode: When each instruction is executed, the service ends the instruction normally without accessing the DB actually |
|||||
| Spool function | Used to store SQL statements when an error occurred and resend the
statements when the communications are recovered from the error |
|||||
| Spool capacity*11 | 192 KB | |||||
| Operation Log function | The following three types of logs can be recorded:
• Execution Log: Log for tracing the executions of the DB Connection Service • Debug Log: Detailed log for SQL statement executions of the DB Connection Service • SQL Execution Failure Log: Log for execution failures of SQL statements in the DB |
|||||
| DB Connection Service Shutdown
function |
Used to shut down the DB Connection Service after automatically saving
the operation log files into the SD Memory Card |
|||||
| Encrypted
Communi- cation |
Supported databases | • SQL Server
• Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| TLS Ver. | TLS 1.2 | |||||
*1. SQL Server 2014, Oracle Database 12c and PostgreSQL 9.4 are supported by the DB Connection Service Version 1.02
or higher.
SQL Server 2016, MySQL 5.7, DB2 11.1 and PostgreSQL 9.5/9.6 are supported by the DB Connection Service Version
1.03 or higher.
SQL Server 2017 is supported by the DB Connection Service Version 1.04 or higher.
Oracle Database 18c, MySQL Community Edition 8.0 and PostgreSQL 10 are supported by the DB Connection Service
Version 2.00 or higher.
You cannot use Oracle 10g with the DB Connection Service version 2.00 or higher.
SQL Server 2019, Oracle Database 19c and PostgreSQL 11/12/13 are supported by the DB Connection Service
Version 2.01 or higher.
SQL Server 2022, Oracle Database 21c/23ai (23c) and PostgreSQL 14/15/16 are supported by the DB Connection
Service Version 2.04 or higher.
*2. Connection to the DB on the cloud is not supported.
*3. The supported storage engines of the DB are InnoDB and MyISAM.
*4. When two or more DB Connections are established, the operation cannot be guaranteed if you set different database
types for the connections.
*5. For the DB Connection Service Version lower than 1.04, Number of DB Connection is 1.
*6. The function is available for the DB Connection Service Version 2.00 or higher.
*7. Depends on members of a structure.
*8. Constrained by the memory capacity for variables. See the specifications for the memory capacity for variables.
*9. Even if the number of DB Map Variables has not reached the upper limit, the maximum total number of members of
structures used as data type of DB Map Variables is 10,000.
*10.For DB Connection Service Version lower than 1.04, Max. number of DB Map Variables for which a mapping can be
connected is 15.
*11.Refer to the NJ/NX-series Database Connection CPU Units User's Manual (Cat. No. W527) for the information.
Note: The extended support for databases has ended for the following DB versions.
Please consider replacing the current database with a new version.
or higher.
SQL Server 2016, MySQL 5.7, DB2 11.1 and PostgreSQL 9.5/9.6 are supported by the DB Connection Service Version
1.03 or higher.
SQL Server 2017 is supported by the DB Connection Service Version 1.04 or higher.
Oracle Database 18c, MySQL Community Edition 8.0 and PostgreSQL 10 are supported by the DB Connection Service
Version 2.00 or higher.
You cannot use Oracle 10g with the DB Connection Service version 2.00 or higher.
SQL Server 2019, Oracle Database 19c and PostgreSQL 11/12/13 are supported by the DB Connection Service
Version 2.01 or higher.
SQL Server 2022, Oracle Database 21c/23ai (23c) and PostgreSQL 14/15/16 are supported by the DB Connection
Service Version 2.04 or higher.
*2. Connection to the DB on the cloud is not supported.
*3. The supported storage engines of the DB are InnoDB and MyISAM.
*4. When two or more DB Connections are established, the operation cannot be guaranteed if you set different database
types for the connections.
*5. For the DB Connection Service Version lower than 1.04, Number of DB Connection is 1.
*6. The function is available for the DB Connection Service Version 2.00 or higher.
*7. Depends on members of a structure.
*8. Constrained by the memory capacity for variables. See the specifications for the memory capacity for variables.
*9. Even if the number of DB Map Variables has not reached the upper limit, the maximum total number of members of
structures used as data type of DB Map Variables is 10,000.
*10.For DB Connection Service Version lower than 1.04, Max. number of DB Map Variables for which a mapping can be
connected is 15.
*11.Refer to the NJ/NX-series Database Connection CPU Units User's Manual (Cat. No. W527) for the information.
Note: The extended support for databases has ended for the following DB versions.
Please consider replacing the current database with a new version.
| Item | Discription |
|---|---|
| Microsoft Corporation: SQL Server | 2008/2008R2 |
| Oracle Corporation: Oracle Database | 10g |
| Oracle Corporation: MySQL Community Edition | 5.1/5.5 |
| International Business Machines Corporation (IBM): DB2 for Linux, UNIX and Windows | 9.5 |
| Firebird Foundation Incorporated: Firebird | 2.1 |
| The PostgreSQL Global Development Group: PostgreSQL | 9.2/9.3 |
last update: July 1, 2025
Top of page
Products
Menu
About Us
Menu
Solutions
Menu
Privacy
Menu
Services
Menu
Resources
Menu
© Copyright OMRON Corporation 2000-2020. All Rights Reserved.