Page top

Industrial Automation

Industrial Automation

EE-SX47 / SX67

Slot-type Photomicrosensor with connector or pre-wired models (Non-modulated)*1

EE-SX47 / SX67

Global Standard Slot-type photomicrosensors with 50- to 100-mA direct switching capacity.

Connector

Appearance Sensing
method
Connecting
method
Sensing
distance
Output
configuration
Indicator
mode
Model
NPN output PNP output
Standard
Through-
beam
type
(with slot)
Connector
(4 poles)
5 mm
(slot
width)
(Infrared
light)
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX670 EE-SX670P
No incident
light
EE-SX670A EE-SX670R
Light-ON Incident light EE-SX470 ---
L-shaped
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX671 EE-SX671P
No incident
light
EE-SX671A EE-SX671R
Light-ON Incident light EE-SX471 ---
T-shaped,
slot
center
7 mm
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX672 EE-SX672P
No incident
light
EE-SX672A EE-SX672R
Light-ON Incident light EE-SX472 ---
Close-
mounting
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX673 EE-SX673P
No incident
light
EE-SX673A EE-SX673R
Light-ON Incident light EE-SX473 ---
Close-
mounting
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX674 EE-SX674P
No incident
light
EE-SX674A EE-SX674R
Light-ON Incident light EE-SX474 ---
T-shaped,
slot
center
10 mm
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX675 EE-SX675P
F-shaped
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX676 EE-SX676P
R-shaped
Dark-ON/
Light-ON
(selectable)
*3 *4
Incident light EE-SX677 EE-SX677P

*3. Dark-ON when the L terminal of the connector is opened, and light-ON when the L terminal and positive (+) terminal are connected. Do not connect the L terminal to 0 V when using dark-ON operation. When using light-ON, it is useful to select the connector EE-1001-1. The L terminal and positive (+) terminal of this connector are connected in advance.
*4. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals.

Pre-wired Models

Appearance Sensing
method
Sensing
distance
Output
configu-
ration
Indicator
mode
Con-
necting
method
Model
NPN output PNP output
Standard 436_lu_2_1 Through-
beam
type
(with slot)
5 mm
(slot
width)
(Infrared
light)
Dark-ON/
Light-ON
(selectable)
*1
Incident
light
Pre-
wired
Models
(1m)
EE-SX670-WR 1M EE-SX670P-WR 1M
L-shaped 436_lu_2_2 EE-SX671-WR 1M EE-SX671P-WR 1M
T-shaped,
slot
center
7 mm
436_lu_2_3 EE-SX672-WR 1M EE-SX672P-WR 1M
Close-
mounting
436_lu_2_4 EE-SX673-WR 1M EE-SX673P-WR 1M
Close-
mounting
436_lu_2_5 EE-SX674-WR 1M EE-SX674P-WR 1M
T-shaped,
slot
center
10 mm
436_lu_2_6 EE-SX675-WR 1M EE-SX675P-WR 1M
F-shaped 436_lu_2_7 EE-SX676-WR 1M EE-SX676P-WR 1M
R-shaped 436_lu_2_8 EE-SX677-WR 1M EE-SX677P-WR 1M

*1. Dark-ON operation can be used when the L terminal is left unconnected or Light-ON operation can be used when the L terminal and positive (+) terminal are connected to each other. Do not connect the L terminal to 0 V when using dark-ON operation.

Accessories (Order Separately) Connector Models

Type Cable length Model Remarks
Connector Connector EE-1001
EE-1001-1 L terminal and positive (+) terminal are
already short-circuited.
EE-1009 *
Connector with Cable 1 m EE-1006 1M
EE-1010 1M *
2 m EE-1006 2M
EE-1010 2M *
Connector with Robot Cable 1 m EE-1010-R 1M *
2 m EE-1010-R 2M *
Connector Hold-down Clip EE-1006A Applicable Photomicrosensors
For EE-SX670[] and 470[] only.
(Can be used only with EE-1006
Connectors for the
Photomicrosensors listed above.)

Note: 1. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals.
   2. For details, refer to the Photomicro Sensors Accessories on EE-[] which can be accessed from your OMRON website.
* EE-1009- or EE-1010-series Connectors have a builtin locking mechanism to prevent cable disconnection when only the cable is pulled. To remove the Connector from the Sensor, grip the top and bottom of the Connector firmly and push into the Sensor once before pulling out. The locking mechanism prevents the Connector from being removed by pulling on the cable only and enables removal only when the Connector (housing) is pulled.